Other | Official Site – Flex Seal® Family Of Products
/Other Announcements

How We’re Helping to Protect First Responders During COVID-19

2020-06-09T12:45:42-04:00

The Flex Seal Family has responded to the COVID-19 pandemic by helping to create life-saving personal protective equipment for our nation’s first responders. Being able to provide assistance to the Healthcare Heroes on the front lines of this pandemic is a privilege. The Flex Seal Family has always supported our nation’s first responders. So, when [...]

How We’re Helping to Protect First Responders During COVID-19 2020-06-09T12:45:42-04:00

How do I use Flex Paste 9 oz cartridges?

2020-04-10T16:04:23-04:00

Flex Paste 9 oz cartridges are designed for use in a caulk gun. Before loading into the caulk gun, be sure to follow the steps below. 1. Unscrew the cartridge tip. 2. Remove the nub with a sharp knife. Try not to remove any of the screw [...]

How do I use Flex Paste 9 oz cartridges? 2020-04-10T16:04:23-04:00

How do I store Flex Paste?

2020-04-10T16:04:04-04:00

Remember that protective foil and silica pack? To prevent your Flex Paste from drying out, replace the protective foil by pressing it on the surface of the material. It is also very important to replace the silica pack too, to prevent Flex Paste from drying out. Continue [...]

How do I store Flex Paste? 2020-04-10T16:04:04-04:00

How do I clean up Flex Paste?

2020-04-10T16:03:46-04:00

Now that your project or repair is complete, it’s time to clean up. Make sure you don’t use water to clean uncured paste. Instead, use a clean dry cloth or paper towel. Mineral spirits and acetone help speed up the process of cleaning your work area. [...]

How do I clean up Flex Paste? 2020-04-10T16:03:46-04:00

Flex Paste™ Helpful Hints

2020-04-10T16:03:30-04:00

Make your job go even smoother using these helpful hints! Spackle and joint compound require sanding, with Flex Paste light sanding is possible, but not recommended. Just smooth it to your desired finish, or add your own artistic texture. It’s all up to you! [...]

Flex Paste™ Helpful Hints 2020-04-10T16:03:30-04:00

How long does it take for Flex Paste to dry?

2020-04-10T16:03:09-04:00

Once Flex Paste is exposed to air or moisture or humidity it begins to cure, forming a skin within 15 to 30 minutes. Flex Paste FULLY cures within 24-48 hours. Remember, it is very important to replace the protective foil as much as possible while you are [...]

How long does it take for Flex Paste to dry? 2020-04-10T16:03:09-04:00

Can I apply Flex Paste on wet surfaces or underwater?

2020-04-10T16:01:11-04:00

Yes, Flex Paste will work underwater and on wet surfaces. For best results, you may want to do some etching in order to increase adhesion. Also, you may need to apply a little extra Flex Paste when working underwater. NEXT STEP Return to Flex Paste 101 [...]

Can I apply Flex Paste on wet surfaces or underwater? 2020-04-10T16:01:11-04:00

How do I apply Flex Paste?

2020-04-10T16:00:53-04:00

With Flex Paste, there is no need to shake or stir, it’s already ready to go!  Grab a putty knife, trowel or similar tool, and remove an even layer of material from the top of the tub. Don’t scoop too deep!  Scooping too deep can cause air pockets that dry [...]

How do I apply Flex Paste? 2020-04-10T16:00:53-04:00

Getting started with Flex Paste™

2020-04-10T16:00:35-04:00

What You Need • Protective gloves, clothing and eye wear • Cloth/rag or Paper towels • Painters tape • Plastic covering or tarp • Flat head screwdriver Using a flat head screwdriver, remove the lid. You see that moisture-absorbing silica pack? Remove it, put it aside and [...]

Getting started with Flex Paste™ 2020-04-10T16:00:35-04:00

What do I do before using Flex Paste?

2020-04-10T16:00:14-04:00

What You Need • Protective gloves, clothing and eye wear • Cloth/rag or Paper towels • Painters tape • Plastic covering or tarp • Flat head screwdriver To get the most out of your Flex Paste, make sure you READ THE DIRECTIONS CAREFULLY. Then follow along [...]

What do I do before using Flex Paste? 2020-04-10T16:00:14-04:00